Hoshizaki DD80-S 80" Stainless Steel Direct Draw Beer Dispenser
DD80-S
Product overview
The Hoshizaki DD80-S serves draft beverages from 2 insulated stainless steel towers with 4 plated brass faucets. Its 80-inch-wide, stainless steel cabinet provides 28.74 cubic feet of interior storage behind 3 solid self-closing, lockable swing doors.
A stainless steel interior, reinforced loading threshold and keg cushion protect the cabinet during keg changes while allowing air to circulate beneath the keg. The heavy-duty 18-gauge stainless steel top supports the dispensing assembly. Interior LED lights illuminate the storage space. Front-breathing, side-mounted refrigeration slides out from the front for qualified cleaning and service.
- 4 faucets: 2 insulated stainless steel towers.
- 80-inch cabinet: Stainless steel exterior front, sides and rear.
- 53-inch total height: Includes the draft towers; plan overhead space accordingly.
Specifications
| Model | DD80-S |
|---|---|
| Type | Direct-draw refrigerated beverage dispenser |
| Cabinet dimensions (W × D × H) | 80 × 29 × 36.88 inches |
| Overall height including tower(s) | 53 inches |
| Depth with door fully open | 51⅛ inches |
| Interior capacity (AHAM) | 28.74 cu. ft. |
| Doors | 3 solid swing doors; self-closing with locks |
| Draft towers | 2 insulated polished stainless steel |
| Faucets | 4 plated brass |
| Exterior front, sides and rear | Stainless steel |
| Interior | Stainless steel with LED lighting |
| Top | 18-gauge stainless steel |
| Loading protection | Stainless steel threshold and keg cushion |
| Refrigerant | R-290 |
| Controller | Electronic LED display; °F or °C |
| Electrical supply | 115V / 60Hz / single phase |
| Plug | NEMA 5-15P |
| Circuit breaker size | 15 A |
| Compressor | 1/3 HP |
Keg and dispensing setup
Plan the keg layout around the cabinet width, keg dimensions and the number of faucets in use. Confirm the intended keg sizes, couplers, gas cylinder, regulator and beverage-line package before ordering. Leave the gauge readable, keep the beer line and keg clear of the evaporator, and allow the door to close without interference.
Have a qualified installer assemble and check the dispensing system. Connect the supplied cold-air channel into each tower as directed in the installation manual so chilled air reaches the dispensing assembly. Check the complete gas and beverage connections for leaks before use; follow the beverage supplier’s requirements for the selected drink and keg connection.
Installation and access
Install indoors on a firm, level floor that supports the fully loaded cabinet. Keep the unit away from ovens, grills and corrosive locations, with unobstructed airflow and room for cleaning and service. Have the installer confirm wall spacing and the operating environment for the delivered model. Allow for the full tower height and open-door depth, not just the cabinet dimensions.
Use a properly grounded electrical supply matched to the delivered nameplate and applicable requirements. If GFCI protection is required, the manufacturer specifies a GFCI breaker rather than a GFCI receptacle. Electrical and refrigeration installation or service should be performed by qualified personnel. Do not stand, climb or hang on the appliance or doors.
Cleaning and maintenance
Keep the condenser clear of dust and grease; clean it every 30–60 days as needed for the installation. Do not add filter material in front of the condenser. Before maintenance, move beverages to suitable cold storage, switch off and unplug the unit. Leave refrigeration work to qualified service personnel.
Clean stainless steel with mild soap and water or a non-abrasive, non-chloride cleaner, then wipe with a soft cloth. Use warm soapy water on door gaskets. Avoid acids, chlorine bleach, steel wool, sharp tools and high-pressure water, and keep electrical parts dry. Keep drain lines clear and the condensate drain tube correctly positioned over its pan. Follow the beverage-system supplier’s cleaning instructions for the lines, faucet and coupler.
Options and model selection
Caster-and-rail kits are available separately. Confirm the kit for the selected cabinet and the resulting installed height. This -S stainless steel exterior model is made to order; confirm availability and lead time.
Compare DD direct-draw dispensers
Choose among five cabinet widths and black vinyl or stainless steel exteriors. Tower, faucet and door counts vary by size. Each model is sold separately.
Product documents
Hoshizaki DD80-S 80" Stainless Steel Direct Draw Beer Dispenser images
