Hoshizaki IM-200BAK 186 lb/Day Air-Cooled Square Cube Ice Machine with Storage Bin
IM-200BAK
Product overview
The Hoshizaki IM-200BAK produces individual 1by1 square ice for beverage service. Its integrated 75 lb nominal storage bin keeps finished ice ready for scooping, and a stainless steel exterior provides a cleanable commercial finish.
The square cubes measure approximately 28 × 28 × 32 mm. A small forming dimple is part of the ice-making process; dimensions are approximate.
- Ice shape: 1by1 square ice.
- Storage: 75 lb nominal.
- Nominal width: 39½ inches; allow the specified ventilation and service space.
Specifications
| Model | IM-200BAK |
|---|---|
| Ice geometry | Approximately 28 × 28 × 32 mm (about 1 × 1 × 1¼ inches) |
| Nominal dimensions (W × D × H) | 39½ × 23⅝ × 33½ inches, including legs |
| Storage | 75 lb nominal |
| Cooling | Self-contained air-cooled |
| Refrigerant | R290 |
| Electrical supply | 115V / 60Hz / single phase; independent grounded supply |
| Connection | NEMA 5-15P plug for a compatible grounded outlet |
| Indoor operating ambient | 45–100°F |
| Potable-water temperature | 45–90°F |
| Water inlet | ½-inch FPT |
| Gravity-drain outlet | ¾-inch FPT |
| Included legs | Five adjustable 6-inch legs |
| Top-panel load limit | 33 lb (15 kg) |
| Production at 70°F air / 50°F water | 186 lb per 24 hours |
| Production at 90°F air / 70°F water | 150 lb per 24 hours |
| Energy at 90°F air / 70°F water | 6.5 kWh per 100 lb |
| Potable water at 90°F air / 70°F water | 23 US gal per 100 lb |
| Minimum circuit / maximum fuse | 15A; verify delivered nameplate |
Daily production and storage are different measures. Select the machine for demand at the actual air and water temperatures, and allow for changes in operating conditions.
Installation and service access
Install level on the five supplied legs. Leave 6 inches on the right and 2 inches behind. On the left and above, choose either 2 inches left with zero above, or ⅝ inch left with 2 inches above. Keep the front air intake and rear discharge clear, and allow access for the bin door and service pull-out.
Nominal cabinet dimensions do not include every utility projection or installation allowance. Check the exact drawing and delivered equipment before fit-out. Keep the machine away from ovens, grills and other high-heat equipment.
R290 siting requirements
The 125 g (4.4 oz) R290 charge is flammable. Provide a room floor area of at least 6.0 m² (64.4 ft²) for operation or storage of this machine. Do not install in a public corridor or lobby. Keep ventilation openings clear and avoid ignition sources in or near the equipment; storage spaces must not contain continuously operating ignition sources. Installation is limited to 2,000 m (6,561 ft) altitude. Use personnel trained for flammable-refrigerant service.
Power, water and drainage
Connect the supplied plug to an independent grounded outlet and confirm the delivered cord reach before locating the outlet. Do not use an extension cord, adapter plug or removed ground pin. If GFCI protection is required, use a GFCI breaker rather than a receptacle.
Provide potable-water shutoff and drain valves. Supply water at 10–113 psig through at least ¼-inch nominal-ID copper tubing or equivalent; fit pressure reduction if needed. Select water treatment for local quality and leave enough line length for service pull-out.
Use at least ¾-inch nominal-ID hard drain pipe or equivalent, a vented tee, at least ¼ inch fall per horizontal foot and a minimum 2-inch vertical air gap to an approved drain. Do not connect directly to a sewer. Have a qualified plumber resolve water hammer before commissioning.
Operation and care
The bin-level control stops production when the storage area fills. Have the installer test the control during commissioning, and keep the sensing mechanism unobstructed. Do not run the water pump in WASH with an empty tank. Wait at least three minutes before restarting after a shutdown.
Clean the scoop daily. Inspect the air filters every two weeks and wash them when dirty. Check external water treatment and wipe the exterior monthly. At least yearly, arrange qualified cleaning and sanitizing of the machine and storage bin, cleaning of the inlet screen, and inspection of hoses and the condenser. Increase the frequency for water quality and site conditions.
Cleaning and sanitizing are separate steps. Disconnect power before service, follow the exact chemical and rinse instructions, wear protective gloves and goggles, and do not use ammonia-type cleaners. Arrange proper draining before prolonged non-use or freezing conditions. The scoop and legs are included; utility installation and optional water-treatment equipment are separate.
Limited warranty
Coverage for the original owner/user includes three years parts and labor on the IM machine and evaporator, plus five years parts on the compressor and air-cooled condenser, subject to the complete terms. Coverage applies in the United States, Canada, Puerto Rico and U.S. territories. Register within 30 days of installation and retain installation records; improper installation, utility faults and inadequate maintenance are among the exclusions. Read the IM limited warranty.
Compare IM specialty-ice machines
IM-50BAA-Q — sphere ice · IM-50BAA-LM — large 2by2 square ice · IM-200BAK — 1by1 square ice · IM-544SAK — 1by1 square ice
Product documents
Hoshizaki IM-200BAK 186 lb/Day Air-Cooled Square Cube Ice Machine with Storage Bin images
